As we all know, the home's water and electricity layout is a hidden project, and its importance is evident. If the toilet pipes are improperly installed, there will be various problems, such as leakage, etc. However, only if you have a certain understanding of the installation of the water pipes, the bathroom in your house can be used normally for a long time, so do not neglect the importance of the installation of the bathroom pipes . Let's learn more about it together!
How to Install Toilet Water Pipes
1, the general bathroom has hot and cold water pipes, the material is mostly PPR pipe, the spacing between the hot and cold pipes can not be too close.
2, bathroom water pipes are from the roof, this can reduce the chance of man-made damage. The interface and outlet of the cold and hot pipes must be parallel. The left side is generally hot and the right side is a cold water pipe.
5472a570160ba03da88b457b.jpg
3, the pipeline design should be to avoid bending, as far away from the circuit. Finally, the position of the tube card, etc., should also meet the requirements. Each valve should be installed flat for future use and maintenance.
4. The cold and hot water pipes are all in the wall. When the slot is to be inspected, the depth of the slot should be checked. The hot and cold water pipes can not be the same as the slot.
5, when installing the water heater inlet and outlet, the inlet valve and the inlet valve must be considered and should be installed in the corresponding position.
6, when installing the hot water pipe should pay attention to the difference between the inlet and outlet of the water heater, water inlet connected to the main valve, outlet connected to the bathroom pipe. After the installation, first open the valve to confirm that there is no leakage, etc. Finally, the faucet and shower can be installed in the bathroom. The shower hose height is between 1.8m-2.1m.
7, is the installation of the bathroom pipe pressure measurement process: Before the pressure test should be closed after the water meter valve, the pressure test pipe end plugging slow water injection, full of water after the sealing inspection, and then manually boost, after the voltage, half The pressure drop within the hour does not exceed 0.05Mpa as qualified.
[Bathroom plumbing installation matters]
1. Change the pipe from the pipe to the pipe and bury it in the pipe.
2, install hot water pipes. Households that use gas water heaters lead the pipelines to the bathroom; homes that use electric water heaters place water heaters in the bathroom and kitchen, and then pick up hot water pipes nearby. Note: The PPR pipe is divided into hot and cold water pipes, and the corresponding pipe wall and pressure resistance are different, and the hot water pipe pipe is thick.
3, change the position of the valve water meter, the water valve to change the low position, and even wrap up, which brings some hidden dangers for future maintenance and work, it is recommended: the total water valve in a better open position. Such as the table, the pipe behind the valve to do low processing; washing machine to move the floor or faucet lead the balcony to wash the mop, watering; water meter high to change the low, --- that rely on the wall to save space, but after putting the cabinet is very Difficult to overhaul and view, the correct way is: by the cabinet, a low vertical wall installation.
4, change the heating pipe, the heater will be moved to facilitate the placement of furniture, such as under the windowsill.
Summary: What are the contents of the above notes about the installation of bathroom plumbing ? It should be noted that the quality and scientificity of the installation of bathroom plumbing must be high, do not underestimate the installation of a plumbing, a good toilet plumbing installation For the use of the bathroom and odor exclusion will help, I hope this article helps everyone.
Toilet Plumbing Leaky Water Pipe Installation Toilet Floor Drain Installation Toilet Decoration Notice Bathroom Installation
Aluminum Wire
Aluminum wiring is a type of electrical wiring for residential construction or houses that uses aluminum electrical conductors. Aluminum provides a better conductivity to weight ratio than copper, and therefore is also used for wiring power grids, including overhead power transmission lines and local power distribution lines, as well as for power wiring of some airplanes.
Aluminum Wire,Aluminum Coil Wire,Aluminum Spool Wire,Aluminum Welding Wire
HENGSHUI YUZHENG IMPORT AND EXPORT CO., LTD. , https://www.ironnailwiremesh.com