Multifunctional aerial pliers using method

Multifunctional aerial pliers

product manual

Multifunctional aerial pliers are special fixtures for temporary wiring when testing or repairing electrical equipment. Over the years, when testing or overhauling electrical equipment that cannot be contacted directly, operators are required to climb up and go wiring. Labor intensity is also not safe. The multifunctional high-altitude wiring pliers solved this problem, transferred traditional high-altitude operations to the ground, fundamentally solved the danger brought by the climb, and greatly improved the working conditions of field operators.

First, the main features:

1, simple operation. With a special operating lever, the upper jaw of the wiring pliers will be stuck on the position where the wiring is required, and the jaws can be freely opened and closed by pushing and pulling the special operating rod to complete the wiring work. The wiring pliers have a large opening size (70mm) and are equipped with a guide mechanism, which is extremely convenient for hanging cards.

2, big force. The principle of the force-reducing pulley is used between the upper and lower jaws of the wiring pliers, so that a larger clamping force can be obtained with a smaller pulling force.

3. There is a clamping force locking and releasing device inside the wiring pliers. When pulling the special operating lever, the inside of the clamp

The elastic energy storage device can automatically lock the jaws at any required force, if not

1

Operating lever, self-locking device will never open, reliable performance. When pushing a dedicated lever,

The release device inside the pliers allows the clamped jaws to be opened for easy operation.

4, good contact. The wiring pliers have the function of overcoming the oxide film at the same time of clamping and ensure that the jaws are in good contact with the wiring position.

5, short-term power current, overload ability.

6, practical and strong. The angle of the clamp head of the wiring pliers can be changed, and the wiring work of different angles, different thicknesses, different diameters, and heights of less than 8 meters in the wiring position can be performed.

7, small weight, light and easy to use. The structural design is reasonable, the texture is excellent, and the durability is long. The weight of the clamp head is less than 700 grams.

Second, use method:

1. Install the wiring pliers on the dedicated operating rod of the required length, install the wires of voltage and current on the terminals of the jaws of the wiring pliers, and then segment the wires (a section near the wiring pliers

Must reserve a 20cm margin), fixed on a dedicated operating lever.

2. Make the pliers of the wiring pliers at a high speed approximately the same angle as the wiring position (if the wiring position is perpendicular to the ground, replace the standby guide hook).

3. Lift the wiring clamp with a special operation lever so that the clamp head slightly leans above the wiring position and leans gently on the wiring position. Reliance on the guide mechanism on the wiring clamp slowly slides downwards at the wiring position. Position, and then slowly use force (do not use too much force) to pull the special operating lever, clamp

2

The mouth is clamped.

4. When removing the wiring pliers, just push the dedicated operating lever to the direction of the wiring pliers and the jaws can be opened.

Third, the use of matters needing attention:

1, must read the user manual before use.

2. When using, you must pay attention to maintaining a safe distance from the charged device!

When using the wiring pliers, all the wires are connected. When lifting or lowering, keep a safe distance from the surrounding devices. Special care must be taken to ensure safety!

3, if the jaws are clamped on the screw, the clamping force is small or the connection line is in bad contact, it will affect the test result.

4. When taking it down after use, be sure to handle it with care.

5. Never push the lower jaw of the wiring pliers upwards, bend or squeeze the steel wire rope inside.

6. Pay attention to the lubrication of sliding parts and avoid dust.

7. It should be kept in a clean and dry place after use.

Multifunctional aerial pliers

#FormatImgID_0#