Decoration is inseparable from the tiles, but where is the tile, how to paste, when the tile grout fill, are related to future use and appearance. Tile wall deformation, grout fall off, not only unsightly, there are still many hidden dangers, we must put an end to these problems, of course, from the beginning to choose the right process.
Before paving 1. The specifications of kitchen and floor tiles should not be too large, the overall size is too large to feel in coordination, and at the same time it is not convenient for ground-mounted floor drains. General kitchen tiles or 330 * 330 specifications are mostly.
2. The bathroom re-tiling the front wall of the tile needs to be treated with waterproof. If you take the method of sticking the tile after putting the wall tile first, you need to do a closed water test before laying the tile. It is better to make the floor waterproof again.
3. Kitchen tiles If you choose waistline and tile, you should consider the position of the tile waist line. The waist line is good on the cabinet of the cabinet. The position of the tile paste should consider the position of the cabinet pendant and the hood. Do not install these objects. Obstructed. Affect the overall coordination and aesthetics.
Links: Paving Tiles Are Stressed to Do Well in 4 Steps
When paving 1. Paste kitchen tiles using cement No. 425 cement, cement sand mixing ratio should not be greater than 1:3, cement content is too heavy, then because of the high coefficient of expansion of the cement caused the cracking of the tiles, reducing the tiles The service life.
2. The glazed wall tiles of kitchen and bathroom If cement mortar is used as the adhesive, the tiles need to be covered with water after soaking, and the time for soaking the water is appropriate after the tiles are completely immersed and does not take bubbles. Generally, it is thirty minutes. That's it.
3. Paving kitchen tiles whether it belongs to a seamless brick, must be left seam, it is recommended not less than 1mm, ordinary wall tiles to 1.5-2mm is appropriate, antique brick gap can be properly widened. The paving height of kitchen and bathroom wall tiles is higher than that of ceilings, generally not less than 10 cm.
4. Pay attention to the texture of the tile when paving the tile, do it along the texture paving, the direction of the waist line of the tile has positive and negative directions should pay attention to its direction, do not paste down, at the same time the texture of the tile waist line and the brick texture consistent.
After the plastering, it is advisable that the jointing is performed after the tiles are completely dried. It usually takes 24 hours.
2. After the floor tiles are tiled, they must wait for the floor to dry before they can walk around the tiles or perform other kitchen and bathroom renovation projects. The wall punching needs attention, and it is best to spray water at the hole where the hole is punched for cooling treatment to prevent the tile from bursting due to the local temperature change of the tiles in a short time.
3. When drilling a hole in the wall, be sure to check if there is any empty drum. Also, check the pipeline diagram of the hydropower reform that has been retained and do not hit the pipeline.
The most problems occurred 1. The grout of bathroom tiles fell off, and some tiles bulged
Analysis of the reasons: Because the light wall of the bathroom is a light steel keel to play the skeleton, the outer seal of the cement board, and the light steel keel spacing is too large, the size is too small, cement mortar and brick are relatively heavy, resulting in deformation of the keel, tile ups , Grafting agent shedding.
Suggestion: The method of palliative treatment is to reapply the grout, but it will fall off as time goes by. The method to cure this problem is to knock out the tiles, change the size of the light steel keel or use a corner brick wall.
2. There is a crack in the door cover of the kitchen, and the MDF of the pipe wrapped around the kitchen is raised
Analysis of the reasons: The kitchen uses the original door and door cover, and the work is relatively rough. The MDF in the kitchen is tilted because it is often soaked. It is a problem of cabinet installation. Cement should be used in such places where water is often encountered.
Solution: Repaint the door cover and make a glass of glue at the crack. The problem of cabinets is more troublesome. If the tiles are to be removed, the cabinets will have to be completely removed and the console and ceiling will be affected. The more realistic method is to glue the aluminum-plastic panel to the area where water is often splashed next to the console. seal.
Tiles Tiles Tiles Tiles Cement Glass paint Glass bricks Cabinets Doors Kitchen ceilings Glass cabinets Kitchen tiles Kitchen cabinets Doors Glass doors Antique bricks Kitchen glass Sliding doors Bathroom tiles Bathroom doors Bathroom tiles Bathroom size Bathroom tiles Bathroom ceilings Overall bathroom Toilets Waterproof toilets Door size tile adhesive kitchen tile tile specification
Xi'an Gavin Electronic Technology Co., Ltd , https://www.gaimcmea.com